Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 13,458. Welcome to our newest member, NeilCo
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 11-15-2016, 04:40 PM
MikeDubber's Avatar
MikeDubber MikeDubber is offline
Platinum
 
Join Date: Jun 2007
Location: Evansville, Indiana
Posts: 476
Default The Titan has arrived !!

I've always been a big-vise engraver - that's why my old Ray LaTourneau Block has always occupied Engraving Bench #1.

Sorry old friend, I moved the 45lb LaTourneau to Bench #2 this afternoon shortly after my new 90 pound Lindsay Titan arrived.

This thing is massive, and unpacking and lifting it in place no easy task. It's also smooooooth, and it doesn't move - at all! For all the good things I can say about the LaTourneau, it's biggest downfall is that it still sits on one of those silly rubber tires, and it just feels spongy. I had gotten used to that, and it really didn't occur to me that the new Lindsay Titan would "work" so solidly. Seriously, the graver action is far more effective when the block (no matter what its weight) sits solidly on the bench, and without the rubber tire absorbing some of the impact of the graver strike. This big boy sits on a solid aluminum ring lined with hard leather - the leather provides enough "tac" to keep the ball tightly held in place. The tension between the block and the base is enough enough that works equally as well with the air graver and the hammer and chisel.

I had been working this Python for the past few weeks. When I placed it in the Titan and started to engraved new lines and scrolls I felt the subtle differences in the graver action immediately.


I have some major inlay and sculpting work to do on this gun, and I just know that all that heavy pounding is going to be so much more effective in this block.

Re: GRS Positioning Block - that used to be at bench #2...now it's in storage. I'm not much of a Microscope user anyway, and it was the heaviest non-LaTourneau available. It's for sale................
Reply With Quote
  #2  
Old 11-17-2016, 09:48 AM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 3,664
Default Re: The Titan has arrived !!

Glad it arrived safe, Mike!.. And it is going right to work! As the Python projects moves along if time allows, please post more pictures of the project.
__________________
__________________________________
Steve Lindsay
www.AirGraver.com
Reply With Quote
  #3  
Old 11-21-2016, 09:42 AM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 3,664
Default Re: The Titan has arrived !!

Quote:
Originally Posted by MikeDubber View Post
I've always been a big-vise engraver - that's why my old Ray LaTourneau Block has always occupied Engraving Bench #1.

Sorry old friend, I moved the 45lb LaTourneau to Bench #2 this afternoon shortly after my new 90 pound Lindsay Titan arrived.

This thing is massive, and unpacking and lifting it in place no easy task. It's also smooooooth, and it doesn't move - at all! For all the good things I can say about the LaTourneau, it's biggest downfall is that it still sits on one of those silly rubber tires, and it just feels spongy. I had gotten used to that, and it really didn't occur to me that the new Lindsay Titan would "work" so solidly. Seriously, the graver action is far more effective when the block (no matter what its weight) sits solidly on the bench, and without the rubber tire absorbing some of the impact of the graver strike. This big boy sits on a solid aluminum ring lined with hard leather - the leather provides enough "tac" to keep the ball tightly held in place. The tension between the block and the base is enough enough that it works equally as well with the air graver and the hammer and chisel.

I had been working this Python for the past few weeks. When I placed it in the Titan and started to engraved new lines and scrolls I felt the subtle differences in the graver action immediately.


I have some major inlay and sculpting work to do on this gun, and I just know that all that heavy pounding is going to be so much more effective in this block.

OK, Steve asked that I post photos of work-in-progression on this Python - so let's walk though the process of inlaying the Colt Onion Dome on the left panel

In this photo I have started preparation by excavating the area of the onion-shaped dome
The 24K dome was sawed out and the relieved area is cross cut to raise burrs

Now the area where the columns are placed is excavated and the area is cross-cut with a "Detail" graver

The inlay is sawed from a 20 ga. piece of fine silver and the inlay cavity is burred up

Both pieces of metal are now hammered into place and smoothed

Now I can continue by designing and cutting the scroll work

The scroll work is completed and I'm ready to detail the inlay

The Colt Onion Dome is detailed - I'm ready to go to the opposite side of the gun to create another Colt inlay.
Notice too, that this left panel is a "cover plate." That is to say that it is placed into an opening that allows the inner working to be installed.
That means that if you are to do a inlaid border (this Python has a double border) you necessarily have to do it in broken sections that
align or register properly when the gun is reassembled.

Super Mike! Thank you for adding more photos of this Python project! Do you have some custom jaws bolted on to the vise? If so, is it using the large 3/8" bolt holes in the top of the jaws or the 1/4" bolt holes?
__________________
__________________________________
Steve Lindsay
www.AirGraver.com
Reply With Quote
  #4  
Old 12-01-2016, 12:59 PM
Mark Diorio Mark Diorio is offline
Steel
 
Join Date: Feb 2016
Location: Vineland, NJ
Posts: 97
Default Re: The Titan has arrived !!

Great work, as usual, Mike. Your work is inspirational to us newbies. That is a huge vise. I'm going to be buying one of Steve's Goliath vises as soon as he has one that is ready to ship. I'm assuming that as a newbie (just under one year since starting engraving), that a Goliath should serve me well for quite some time?
Reply With Quote
  #5  
Old 12-02-2016, 09:01 AM
SEngraver SEngraver is offline
Platinum
 
Join Date: Sep 2008
Location: UK.
Posts: 3,273
Default Re: The Titan has arrived !!

Hi
Mike thank you for the work in progress pictures of the python revolver.
The pictures were interesting and intuitive.
Most Appreciated
SE
__________________
Learn from those who know more than you do and teach those who know less than you do. - I.M.
Reply With Quote
  #6  
Old 12-02-2016, 09:07 AM
Brian Brian is offline
Platinum
 
Join Date: Apr 2006
Location: Stockton, California & Taxco, Guerrero, Mexico
Posts: 787
Default Re: The Titan has arrived !!

Steve is probably already working on a vise big enough for helicopter parts...

And perhaps an Airgraver big enough to work on stone monuments?

Brian
Reply With Quote
  #7  
Old 12-02-2016, 02:30 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 3,664
Default Re: The Titan has arrived !!

Hi Mark, A guesstimate for when the updated stainless Goliaths are ready is mid to late January.

Quote:
Originally Posted by Brian View Post
Steve is probably already working on a vise big enough for helicopter parts...
And perhaps an Airgraver big enough to work on stone monuments?Brian
Brian! Only under 10' foot high monuments!
__________________
__________________________________
Steve Lindsay
www.AirGraver.com
Reply With Quote
  #8  
Old 12-06-2016, 03:56 AM
CMan CMan is offline
Copper
 
Join Date: Nov 2016
Location: Sebastian
Posts: 1
Default Re: The Titan has arrived !!

I loved always as a youth looking at that dome driving by in the family car. Later in years watching it being restored. Now to see it engraved on a gun. Thanks, Cliff
Reply With Quote
  #9  
Old 12-06-2016, 03:15 PM
Mark Diorio Mark Diorio is offline
Steel
 
Join Date: Feb 2016
Location: Vineland, NJ
Posts: 97
Default Re: The Titan has arrived !!

Quote:
Originally Posted by Steve Lindsay View Post
Hi Mark, A guesstimate for when the updated stainless Goliaths are ready is mid to late January.



Brian! Only under 10' foot high monuments!


Thanks, Steve.
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 03:38 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.