Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,732. Welcome to our newest member, Miss Allison
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 08-06-2010, 02:05 PM
carl bleile's Avatar
carl bleile carl bleile is offline
Platinum
 
Join Date: Mar 2008
Location: cincinnati,ohio
Posts: 380
Default Cutting with the NITRO G20

My intention on getting the Nitro G20 was to see how it would aid in deep relief and sculpting, but at the request of one of my students who engraves motorcycle parts and others whom work in softer metals I did a little cutting on aluminum.

First I ground a tool using the 110 degree sharpening template, the only adjustment was sharpening the face, I raised the template approx. 3/16 in.so the tool wouldn't dig into the softer metal.

Second I sketched a design that I thought could be used on a motorcycle part, something not to detailed as this would be viewed from 3 feet away and more angled cuts for reflections.

After making a few test cuts I started scroll cuts without using an optivisor because the design was to large. The Nitro really did its job, the cutting was to the point of being easy, I relaxed and just guided the tool. Basic cuts were done in 5 minutes or so then I added some small reflective cuts and finished up by dulling the background with a punch. I was tempted to do a more refined design but had to remember that in this type of work there would be a lot of area to cover and time is important.

To sum up my thoughts on the Nitro G20 it is an impressive tool, it allows more freedom of design, cuts down on engraving time and physical stress. Its capable of very large work while at the same time smooth enough for classic work in harder metals.
Attached Images
File Type: jpg DSC00106.jpg (48.1 KB, 251 views)
File Type: jpg DSC00107.jpg (56.4 KB, 244 views)
File Type: jpg DSC00108.jpg (92.6 KB, 278 views)
File Type: jpg DSC00109.jpg (83.0 KB, 255 views)
File Type: jpg DSC00110.jpg (76.0 KB, 245 views)
File Type: jpg DSC00111.jpg (86.7 KB, 258 views)
File Type: jpg DSC00113.jpg (94.0 KB, 292 views)
File Type: jpg DSC00116.jpg (81.8 KB, 277 views)
File Type: jpg DSC00118.jpg (75.2 KB, 267 views)
File Type: jpg DSC00120.jpg (74.6 KB, 292 views)
Reply With Quote
  #2  
Old 08-06-2010, 03:09 PM
jlseymour's Avatar
jlseymour jlseymour is offline
Platinum
 
Join Date: Feb 2007
Location: Mt. Dora FL
Posts: 1,568
Default Re: Cutting with the NITRO G20

Darn you Carl you gonna make me order one...
I don't need anything else...
Hope to visit someday, but I don't need a carry pistol...
That was so cool and I hope Scott enjoyed the pain, He did with the shine ya'll filled him with...
Thanks Carl
Jerry
Reply With Quote
  #3  
Old 08-06-2010, 07:45 PM
rodsta rodsta is offline
Gold
 
Join Date: Jun 2008
Location: Arkansas
Posts: 134
Default Re: Cutting with the NITRO G20

Ditto on that Jerry!!! I was holding off in getting one but it looks like I'm doomed to add another tool to the arsenal. I'm planning on a Harley carving soon so it should come in handy.
Thanks for the review Carl. Sorry we didn't get your carving demo at the Engrave in. I was looking forward to it. Maybe next year.
Rod
Reply With Quote
  #4  
Old 08-07-2010, 10:46 PM
AndrosCreations's Avatar
AndrosCreations AndrosCreations is offline
Platinum
 
Join Date: May 2009
Location: Northeastern Ohio
Posts: 374
Default Re: Cutting with the NITRO G20

Greetings Mr. Bleile,

Thanks for the review of the nitro. It sounds like a beast...

"I added some small reflective cuts and finished up by dulling the background with a punch"

Did you do the background with a hammer and punch, or was it mounted in the airgraver?

Thanks,
Andy
__________________
Andy Gonzales
Proverbs 3:6 In all your ways acknowledge Him, and He shall direct your paths.

www.androscreations.com
Reply With Quote
  #5  
Old 08-08-2010, 07:07 PM
KDavid's Avatar
KDavid KDavid is offline
Platinum
 
Join Date: Jun 2006
Location: Orlando, Florida
Posts: 561
Default Re: Cutting with the NITRO G20

Hey Jerry and Rod..........what are you guys waiting for, I've owned one for several months now and wouldn't want to be without one. if your not careful you can engrave roght through the practice plate Lol
__________________
David Gruber
WWW.Sharpgraver.com
"The democracy will cease to exist when you take away from those who are willing to work and give to those who would not."
Thomas
Jefferson
Reply With Quote
  #6  
Old 08-08-2010, 09:46 PM
JohnR's Avatar
JohnR JohnR is offline
Platinum
 
Join Date: Sep 2008
Location: Modesto, CA
Posts: 241
Default Re: Cutting with the NITRO G20

Hello Carl, I also wanted to see what the G20 could do and today I spent some time at Brian Marshall's School in Stockton for a test run. It's a "thumper". I tested it using the 1/8" graver and was very impressed with its power to hog out metal. The control was as you said just point it in the direction and let it go, just remember to hang on and keep your free hand clear. Also the size was purfect for my big hands. This is a great machine for motorcycle and car engraver......JohnR. Also a big Thank You to Brian Marshall for the free demonstration.
Reply With Quote
  #7  
Old 08-09-2010, 07:35 AM
shovelrider's Avatar
shovelrider shovelrider is offline
Steel
 
Join Date: May 2010
Location: Sadieville, Ky
Posts: 41
Default Re: Cutting with the NITRO G20

I mostly Engrave parts for Motorcycles and Hot Rods. I bought a Nitro G20 this spring and would not ever want to work without it. It is truely an amazing little machine.
__________________
Cool can not be bought, it must be made by hand

Robert "Bid" Bidwell
Reply With Quote
  #8  
Old 08-09-2010, 07:56 AM
rodsta rodsta is offline
Gold
 
Join Date: Jun 2008
Location: Arkansas
Posts: 134
Default Re: Cutting with the NITRO G20

Kdavid- I know. It seems inevitable. I just need to order one up. Sounds like too much fun.

Shovelrider- do you suggest using the 1/8 gravers or do you find that the smaller ones are enough fir motorcycle engraving?
Rod
Reply With Quote
  #9  
Old 08-09-2010, 07:18 PM
shovelrider's Avatar
shovelrider shovelrider is offline
Steel
 
Join Date: May 2010
Location: Sadieville, Ky
Posts: 41
Default Re: Cutting with the NITRO G20

Rod, I use 1/8". When doing Motorcycle parts you have to plow deep for it to be visible. Remember you are looking at it parked at the curb. They also work fine if you have to lighten up.
__________________
Cool can not be bought, it must be made by hand

Robert "Bid" Bidwell
Reply With Quote
  #10  
Old 09-02-2010, 09:05 PM
JMBarnes JMBarnes is offline
Copper
 
Join Date: Jul 2010
Location: Mission Viejo, CA
Posts: 3
Default Re: Cutting with the NITRO G20

Physical stress from engraving?
J Barnes
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 06:18 AM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.