Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community

The Internet's Largest and Fastest Growing Engraving Community
Discuss hand engraving using basic to the most advanced methods and equipment
Forum Members: 14,761. Welcome to our newest member, AnicaLin
EngravingForum.com - Domain since Feb 7, 2003

Graver Video Conferencing is empty Join now!


Go Back   Engraving Forum.com - The Internet's Largest and Fastest Growing Engraving Community > Forums > Lindsay AirGraver Info - Hand Engraving Forum
ENGRAVING TOOLS - Paypal accepted Classes Glossary Feedback Tips Sharpening Bulino Videos Forum Policies

Reply
 
Thread Tools
  #1  
Old 08-08-2008, 12:52 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Sharpener length gauge distances

I can’t find the thread now, but some time ago someone requested the various distances and resulting angles for the sharpener. The length gauge that you received with the fixture is 1-Ľ long. It will produce a 45 degree face, 16.3 degree high heel. If you instead lock the graver in so it is protruding 1-5/8” it will make a 41 degree face with a 14 degree high heel. Setting the length to 7/8” will produce a 50 degree face with a 19.5 degree high heel. The measurement is from the shoulder on the sharpener. Check where the shipped length gauge measures from. That is the shoulder to measure from. If you’re grinding one of the uniform-parallel heeled gravers be sure to grind the long relief grinds on the bottom of the graver as well as the small heel and the face with the graver sticking out the same length so the heels come out uniform.

1.625" = 41 face, 14.0 high heel
1.250" = 45 face, 16.3 high heel
0.875" = 50 face, 19.5 high heel
Sharpening instructions
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #2  
Old 08-08-2008, 02:14 PM
jlseymour's Avatar
jlseymour jlseymour is offline
Platinum
 
Join Date: Feb 2007
Location: Mt. Dora FL
Posts: 1,568
Default Re: Sharpener length gauge distances

Thanks Steve, this helps allot...
I had ask before if I set the diamond stone off the large blue square and set it on the table below that would change all the angles, especially the heel...
Your info is so much better than my guessing...
Jerry
Reply With Quote
  #3  
Old 08-08-2008, 08:20 PM
SpiderCurt's Avatar
SpiderCurt SpiderCurt is offline
Steel
 
Join Date: Jun 2008
Location: Kentucky
Posts: 95
Default Re: Sharpener length gauge distances

Hi Steve
I want to thank you too! As a "newbie", I appreciate it when someone takes the time to answer dumb questions as you did in a recent e-mail. I have learned enough, so far, to realize that the information posted in this thread can be used to make the sharpening fixture much more versatile. As for now, this info is being filed away until such time as I am satisfied with my control of a graver.
__________________
Curt Myers

My Picture Album
Reply With Quote
  #4  
Old 08-09-2008, 01:18 AM
Vanknife Vanknife is offline
Platinum
 
Join Date: Mar 2007
Location: Florauna Park Pretoria South Africa
Posts: 350
Default Re: Sharpener length gauge distances

Thanks Steve,
I will have to make use of the convertion table now.
Cheers

"VAN"
Reply With Quote
  #5  
Old 08-09-2008, 12:12 PM
SVD's Avatar
SVD SVD is offline
Platinum
 
Join Date: Mar 2008
Location: Kansas City, MO
Posts: 2,555
Default Re: Sharpener length gauge distances

Printed off for my records. I'll have to make (and label) a set of guages.
__________________
Enjoy!

Steve :->
(KCSteve in most forums)
SVD's Photo Album
Reply With Quote
  #6  
Old 08-09-2008, 12:40 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Sharpener length gauge distances

Good, glad it helps. I did made an adjustable length gauge. The fixed length gauges do seem to be more quick and repeatable during use.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #7  
Old 08-27-2008, 12:01 AM
monk monk is offline
Platinum
 
Join Date: Apr 2006
Posts: 828
Default Re: Sharpener length gauge distances

thanks, steve. i had asked sometime ago about this very thing. good to know about the 50 degree one. thanks again.
Reply With Quote
  #8  
Old 08-09-2014, 07:23 PM
Toad Toad is offline
Gold
 
Join Date: Mar 2008
Location: Vermilion, Ohio
Posts: 123
Default Re: Sharpener length gauge distances

What length for 55 and 60 degrees
Reply With Quote
  #9  
Old 08-19-2014, 06:21 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Sharpener length gauge distances

Hi Toad, I don't know without pulling up the cad file to calculate exactly. But it would be shorter than .875" since that is 50 degrees. .750" I bet would be pretty close and it is an easier number to remember. Instead of going shorter with the length that the graver is sticking out we can instead just raise the height that the template sets or lower the stone height. Or you can do a combination of both. Whatever you do, do it for all the facets (small and large template) so that the heels come out parallel.
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #10  
Old 10-20-2019, 06:06 AM
Ralph René's Avatar
Ralph René Ralph René is offline
Steel
 
Join Date: Mar 2017
Location: Germany
Posts: 58
Default Re: Sharpener length gauge distances

Hi Steve, since you opened my eyes of using a much shorter heel, problems with heeldrag became much less.
But for example heavy cuts of small curves which are tapered on a short way to both ends still causing heeldrag from time to time. Maybe it’s my personal and wrong way of holding the airgraver?! When I try to come out of the metal ( heel really is short) I often scratch the outer edge.
Could 0.875" = 50 face, 19.5 high heel be a better angle for me or could I try something different?
With the naked eye it’s all nice, but with magnification it’s not yet perfect Best regards
Ralph Rene
Attached Images
File Type: jpeg E5842DD6-7F8A-4881-B5F3-4980CF9C2FE5.jpeg (63.8 KB, 0 views)
Reply With Quote
  #11  
Old 10-21-2019, 04:36 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Sharpener length gauge distances

Quote:
Originally Posted by Ralph René View Post
Hi Steve, since you opened my eyes of using a much shorter heel, problems with heeldrag became much less.
But for example heavy cuts of small curves which are tapered on a short way to both ends still causing heeldrag from time to time. Maybe it’s my personal and wrong way of holding the airgraver?! When I try to come out of the metal ( heel really is short) I often scratch the outer edge.
Could 0.875" = 50 face, 19.5 high heel be a better angle for me or could I try something different?
With the naked eye it’s all nice, but with magnification it’s not yet perfect Best regards
Ralph Rene
Hi Ralph,

Yes, steep face and wide V will be a stronger point. Also dubbing the point. Dubbing is described clear at the bottom of this page:
https://www.engravingschool.com/priv...0Sharpener.htm



Also Bulldozering the two cutting edges. Similar to dubbing but instead of the point you do it to the two cutting edges.







I have another 116 degree template that has a 50 degree face. Also thanks to Rick Simmons and Wes Griffin there is another set that is steeper yet. They are at the top of this page link: "Friction" https://www.airgraver.com/news.htm
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
  #12  
Old 07-19-2020, 02:06 PM
Ralph René's Avatar
Ralph René Ralph René is offline
Steel
 
Join Date: Mar 2017
Location: Germany
Posts: 58
Default Re: Sharpener length gauge distances

Hi everybody,
for all goldsmiths out there practicing inside ring engravings I just want to share what I found out.
For all new engravers like me it’s very frustrating inside rings without perfect graver control. Cuved surface, limited clearance and very small script letters often ending up in heeldrag. Gravers sharpened with the 22.2 mm length gauge gave me a completely different feeling compared to the normal ones. I immediately got a much better result, nice small letters without any heeldrag. If you are a beginner like me, you definitely should try it with a length gauge of 22.2 mm. It helped me A LOT!
Reply With Quote
  #13  
Old 07-19-2020, 06:03 PM
Steve Lindsay's Avatar
Steve Lindsay Steve Lindsay is offline
Administrator
 
Join Date: Feb 2006
Location: Kearney, NE
Posts: 4,555
Default Re: Sharpener length gauge distances

Quote:
Originally Posted by Ralph René View Post
Hi everybody,
for all goldsmiths out there practicing inside ring engravings I just want to share what I found out.
For all new engravers like me it’s very frustrating inside rings without perfect graver control. Cuved surface, limited clearance and very small script letters often ending up in heeldrag. Gravers sharpened with the 22.2 mm length gauge gave me a completely different feeling compared to the normal ones. I immediately got a much better result, nice small letters without any heeldrag. If you are a beginner like me, you definitely should try it with a length gauge of 22.2 mm. It helped me A LOT!
Hi Ralph! Good good! For us inch people 22.2mm is .875" (7/8"). You must then be at around a 50 face and 20 high heel.

0.875" = 50 face, 19.5 high heel
__________________
__________________________________
Steve Lindsay
AirGraver.com
EngravingArtist.com
Reply With Quote
Reply

Bookmarks

Thread Tools

Posting Conduct
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -6. The time now is 09:05 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.